I am looking to sell my 60g Cube setup with custom stand. Some of you old timers might remember this as Walter White's (Chris) old setup. I upgraded the tank to an external overflow setup using the Modular Marine 1200 gph low profile overflow. This upgrade is not shown in the older photos below.
60g Cube glass aquarium (2'x 2'x 2')
Custom built wood stand with doors on three sides
Modular Marine 1200gph low profile external overflow, Bean Animal setup
Schedule 80 plumbing
20g glass sump
2x Eheim 1260-310 return pumps (one is a spare I swap in when cleaning the other)
2x 1/2" Sea Swirl wave makers
1x Eheim heater
1x Colbalt heater
3x BRS 1.1 dosing pumps
3x BRS small footprint containers
Reef Octopus Classic-110 SSS skimmer
6~8x 4" filter socks
3x probe holder
2x 25g roto-mold mixing tanks and stands (RODI system not included)
Asking $500 OBO
The following Apex and Radion gear are add-on options:
1x Apex AFS auto feeder +$50
1x Apex WM module (used for Radion listed below) +$80
1x Radion XR30 Pro Gen 4 (Mobius capable) +$400
Buy the complete setup for $850.
Quarter sawn white oak stand
View attachment 20317
The old ReefLink module is not on the stand any longer.
View attachment 20318
Doors open on three sides and the canopy lid opens to the front. The canopy can be completely removed. Note that all of the hinges are hidden for a super clean look.
View attachment 20319
This is looking at the sump from the right side of the tank. There are now three of the BRS dosing pumps mounted.
View attachment 20322
This is the sump area from the front of the tank showing where two of the slim profile dosing containers site. The third would sit next to the sump in the photo above
View attachment 20323
There is a wooden section that separates the sump from the electronics section. The BRS dosing pumps are mounted on one side and electronics can be mounted on the other. The below photo shows it setup with my Apex gear (not included in this sale). The wire management traces come with the tank.
View attachment 20324
I made a custom acrylic gantry to go across the top of the tank to hold an Apex auto feeder. You can also see the two Sea Swirls and the gate valve used to control flow to each side.
View attachment 20321
The acrylic gantry has a holder for the Apex Aquabus cable so that it does not slide back behind the tank.
View attachment 20320
More pictures of the Sea Swirls and how they are plumbed (the line lock tubing shown does not come with this setup, I'm using it on my new tank).
View attachment 20325
60g Cube glass aquarium (2'x 2'x 2')
Custom built wood stand with doors on three sides
Modular Marine 1200gph low profile external overflow, Bean Animal setup
Schedule 80 plumbing
20g glass sump
2x Eheim 1260-310 return pumps (one is a spare I swap in when cleaning the other)
2x 1/2" Sea Swirl wave makers
1x Eheim heater
1x Colbalt heater
3x BRS 1.1 dosing pumps
3x BRS small footprint containers
Reef Octopus Classic-110 SSS skimmer
6~8x 4" filter socks
3x probe holder
2x 25g roto-mold mixing tanks and stands (RODI system not included)
Asking $500 OBO
The following Apex and Radion gear are add-on options:
1x Apex AFS auto feeder +$50
1x Apex WM module (used for Radion listed below) +$80
1x Radion XR30 Pro Gen 4 (Mobius capable) +$400
Buy the complete setup for $850.
Quarter sawn white oak stand
View attachment 20317
The old ReefLink module is not on the stand any longer.
View attachment 20318
Doors open on three sides and the canopy lid opens to the front. The canopy can be completely removed. Note that all of the hinges are hidden for a super clean look.
View attachment 20319
This is looking at the sump from the right side of the tank. There are now three of the BRS dosing pumps mounted.
View attachment 20322
This is the sump area from the front of the tank showing where two of the slim profile dosing containers site. The third would sit next to the sump in the photo above
View attachment 20323
There is a wooden section that separates the sump from the electronics section. The BRS dosing pumps are mounted on one side and electronics can be mounted on the other. The below photo shows it setup with my Apex gear (not included in this sale). The wire management traces come with the tank.
View attachment 20324
I made a custom acrylic gantry to go across the top of the tank to hold an Apex auto feeder. You can also see the two Sea Swirls and the gate valve used to control flow to each side.
View attachment 20321
The acrylic gantry has a holder for the Apex Aquabus cable so that it does not slide back behind the tank.
View attachment 20320
More pictures of the Sea Swirls and how they are plumbed (the line lock tubing shown does not come with this setup, I'm using it on my new tank).
View attachment 20325
